Head on this page.

Panasonic ideas for life Global
Search Panasonic Global Site

PT-DZ12000 Series

3-chip DLP™ Projector PT-DZ12000/PT-D12000
Incredible Brightness & High Picture QualityHigh Reliability & StabilityEnhanced Installation Flexibility
Main Parts and Controls Specifications Standard Setting-up Positions Optional Accessories

PT-DZ12000
PT-D12000
PT-DW100
Specifications  

  PT-DZ12000
  PT-DZ12000
DLP™ chip Panel size 0.96" diagonal (16:10 aspect ratio)
Display method DLP™ chip x 3 (R, G, B), DLP™ projection system
Pixels 2,304,000 (1,920 x 1,200) x 3, total of 6,912,000 pixels
Lamp 300 W UHM lamp x 4 (four lamp system)
Brightness*1 12,000 lumens (four-lamp operation mode)
Contrast ratio*1 5,000:1 (full on/full off, in Dynamic iris 3 mode)
Resolution 1,920 x 1,200 pixels
Lens Optional powered zoom/focus lenses 
Screen size 70 - 600 inches,16:10 aspect ratio
(70-300 inches, 16:9 aspect ratio with the ET-D75LE5)
Lens shift*2 Vertical: ±55% (±44° with the ET-D75LE6) from center of screen, powered
Horizontal: ±20% (±15° with the ET-D75LE6) from center of screen, powered
Scanning frequency RGB fH 15-100 kHz, fV 24-120 Hz*3
Dot clock 20-162 MHz
YPBPR (YCBCR) 480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p,
1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p
S-Video/Video fH 15.75/15.63 kHz, fV 50/60Hz
(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)
Terminals VIDEO IN BNC x 1, 1.0 Vp-p
VIDEO OUT BNC x 1, 1.0 Vp-p
S-VIDEO IN Mini DIN 4-pin x 1
RGB 1 / YPBPR IN BNC x 5
RGB 2 IN D-sub HD 15-pin x 1
DVI-D IN DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p
VGA (640 x 480) – WUXGA*4 (1,920 x 1,200), compatible with non-interlaced signals only, Dot clock: 25–162 MHz
SERIAL IN*5 D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)
SERIAL OUT*5 D-sub 9-pin male x 1 (RS422 x 1)
REMOTE 1 IN M3 jack x1 for wired remote control
REMOTE 1 OUT M3 jack x1 for link control
REMOTE 2 IN D-sub 9-pin female x 1 for external control (parallel)
LAN RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™
Optional board slot*6 With ET-MD77SD1 installed
SERIAL IN:   BNC x 1
SD-SDI signal (YPBPR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i

SERIAL OUT:   BNC x 1, active through
With ET-MD77SD3 installed
SERIAL IN:   BNC x 1
SD-SDI signal (YPBPR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YPBPR 4:2:2 10-bit) : SMPTE 292M compliant 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p

SERIAL OUT:   BNC x 1, active through
With ET-MD100SD4 installed
Link A/Link B IN:   BNC x 1 for each
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 292M compliant, 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit) : SMPTE 372M compliant, 1920 x 1080/50i, 1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit) : 2048 x 1080/24p, 2048 x 1080/24sF
With ET-MD77DV installed
DVI-D IN:   DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p
VGA (640 x 480) – WUXGA*4 (1,920 x 1,200), compatible with non-interlaced signals only, Dot clock: 25–162 MHz
Keystone correction range Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6),
Using Geometric Adjustment: Vertical ±10°, Horizontal ±15°
Installation Front/rear, ceiling/floor
Power cord length 9.9'' (3.0 m)
Power supply PT-DZ12000U
(North America)		 120 VAC, 9-16A, 50/60Hz
PT-DZ12000E
(Europe, Asia)		 240 VAC, 9-16A, 50/60Hz
Power consumption PT-DZ12000U
(North America)		 1,600–1,500 W (10–15 W in standby mode with fan stopped)
PT-DZ12000E
(Europe, Asia)		 1,500 W (15 W in standby mode with fan stopped)
Dimensions (W x H x D) 22-3/4'' x 12-19/32'' x 25-5/16'' (578 x 320 x 643 mm) (without lens)
Weight*7 77.1 lbs (35 kg) without lens
Operating temperature*8 32-113 ° F (0-45°C)
Operating humidity 10-80% (no condensation)
Supplied accessories Power cord, Wireless/wired remote control unit, Batteries for remote control (AA type for North/South America, R6/LR6 type for Europe / Asia) x 2, Eye bolts (x4), Wire rope

*1: Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*2: Shift range is limited during simultaneous horizontal and vertical shifting.
*3: Smooth image reproduction may not be possible when a motion video signal with a vertical frequency other than 50 or 60 Hz is input.
*4: WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5: Contact your dealers for details when the control using RS-232C or RS-422 is required.
*6: The LAN terminal on the optional board will be inactivated after installation. Use the LAN terminal on the main unit.
*7: Average value. May differ depending on models.
*8: The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]). Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be reduced approximately 30% to protect the projector.
Return to Top
PT-DZ12000
PT-D12000
PT-DW100

  PT-D12000
PT-D12000
DLP™ chip Panel size 0.95" diagonal (4:3 aspect ratio)
Display method DLP™ chip x 3 (R, G, B), DLP™ projection system
Pixels 1,470,000 (1,400 x 1,050) x 3, total of 4,410,000 pixels
Lamp 300 W UHM lamp x 4 (four lamp system)
Brightness*1 12,000 lumens (four-lamp operation mode)
Contrast ratio*1 5,000:1 (full on/full off, in Dynamic iris 3 mode)
Resolution 1,400 x 1,050 pixels (1,920 x 1,200 pixels compatible, compression mode)
Lens Optional powered zoom/focus lenses
Screen size 70 - 600 inches, 4:3 aspect ratio
(70-300 inches, 4:3 aspect ratio with the ET-D75LE5)
Lens shift*2 Vertical: ±50% (±40° with the ET-D75LE6) from center of screen, powered
Horizontal: ±30% (±20° with the ET-D75LE6) from center of screen, powered
Scanning frequency RGB fH 15-100 kHz, fV 24-120 Hz*3
Dot clock 20-162 MHz
YPBPR (YCBCR) 480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p
S-Video/Video fH 15.75/15.63 kHz, fV 50/60Hz
(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)
Terminals VIDEO IN BNC x 1, 1.0 Vp-p
VIDEO OUT BNC x 1, 1.0 Vp-p
S-VIDEO IN Mini DIN 4-pin x 1
RGB 1 / YCBCR IN BNC x 5
RGB 2 IN D-sub HD 15-pin x 1
DVI-D IN DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p
VGA (640 x 480) – WUXGA*4 (1,920 x 1,200), compatible with non-interlaced signals only, Dot clock: 25–162 MHz
SERIAL IN*5 D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)
SERIAL OUT*5 D-sub 9-pin male x 1 (RS422 x 1)
REMOTE 1 IN M3 jack x1 for wired remote control
REMOTE 1 OUT M3 jack x1 for link control
REMOTE 2 IN D-sub 9-pin female x 1 for external control (parallel)
LAN RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™
Optional board slot*6 With ET-MD77SD1 installed
SERIAL IN:   BNC x 1
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i

SERIAL OUT:   BNC x 1, active through
With ET-MD77SD3 installed
SERIAL IN:   BNC x 1
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 292M compliant 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p

SERIAL OUT:   BNC x 1, active through
With ET-MD100SD4 installed
Link A/Link B IN:   BNC x 1 for each
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 292M compliant, 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit) : SMPTE 372M compliant, 1920 x 1080/50i, 1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit) : 2048 x 1080/24p, 2048 x 1080/24sF
With ET-MD77DV installed
DVI-D IN:   DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p
VGA (640 x 480) – WUXGA*4 (1,920 x 1,200), compatible with non-interlaced signals only, Dot clock: 25–162 MHz
Keystone correction range Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6),
Using Geometric Adjustment: Vertical ±10°, Horizontal ±15°
Installation Front/rear, ceiling/floor
Power cord length 9.9'' (3.0 m)
Power supply PT-D12000U
(North America)		 120 VAC, 9-16A, 50/60Hz
PT-D12000E
(Europe, Asia)		 240 VAC, 9-16A, 50/60Hz
Power consumption PT-D12000U
(North America)		 1,600–1,500 W (10–15 W in standby mode with fan stopped)
PT-D12000E
(Europe, Asia)		 1,500 W (15 W in standby mode with fan stopped)
Dimensions (W x H x D) 22-3/4'' x 12-19/32'' x 25-5/16'' (578 x 320 x 643 mm) (without lens)
Weight*7 77.1 lbs (35 kg) without lens
Operating temperature*8 32-113 °F (0-45°C)
Operating humidity 10-80% (no condensation)
Supplied accessories Power cord, Wireless/wired remote control unit, Batteries for remote control (AA type for North/South America, R6/LR6 type for Europe / Asia) x 2, Eye bolts (x4), Wire rope

*1: Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*2: Shift range is limited during simultaneous horizontal and vertical shifting.
*3: Smooth image reproduction may not be possible when a motion video signal with a vertical frequency other than 50 or 60 Hz is input.
*4: WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5: Contact your dealers for details when the control using RS-232C or RS-422 is required.
*6: The LAN terminal on the optional board will be inactivated after installation. Use the LAN terminal on the main unit.
*7: Average value. May differ depending on models.
*8: The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]). Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be reduced approximately 30% to protect the projector.
Return to Top
PT-DZ12000
PT-D12000
PT-DW100

  PT-DW100
PT-DW100
DLP™ chip Panel size 0.85" diagonal (16:9 aspect ratio)
Display method DLP™ chip x 3 (R, G, B), DLP™ projection system
Pixels 1,049,088 (1,366 x 768) x 3, total of 3,147,264 pixels
Lamp 300 W UHM lamp x 4 (four lamp system)
Brightness*1 10,000 lumens (four-lamp operation mode)
Contrast ratio*1 5,000:1 (full on/full off, in Dynamic iris 3 mode)
Resolution 1,366 x 768 pixels (1,920 x 1,200 pixels compatible, compression mode)
Lens Optional powered zoom/focus lenses
Screen size 70 - 600 inches, 16:9 aspect ratio
(70-300 inches, 16:9 aspect ratio with the ET-D75LE5)
Lens shift*2 Vertical: ±70% (±60° with the ET-D75LE6) from center of screen, powered
Horizontal: ±30% (±20° with the ET-D75LE6) from center of screen, powered
Scanning frequency RGB fH 15-100 kHz, fV 24-120 Hz*3
Dot clock 20-162 MHz
YPBPR (YCBCR) 480i, 480p, 576i, 576p, 720/60p, 720/50p, 1035/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p, 1080/60i, 1080/50i, 1080/50p, 1080/60p
S-Video/Video fH 15.75/15.63 kHz, fV 50/60Hz
(NTSC,NTSC4.43,PAL,PAL60,PAL-N,PAL-M,SECAM)
Terminals VIDEO IN BNC x 1, 1.0 Vp-p
VIDEO OUT BNC x 1, 1.0 Vp-p
S-VIDEO IN Mini DIN 4-pin x 1
RGB 1 / YPBPR IN BNC x 5
RGB 2 IN D-sub HD 15-pin x 1
DVI-D IN DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p
VGA (640 x 480) – WUXGA*4 (1,920 x 1,200), compatible with non-interlaced signals only, Dot clock: 25–162 MHz
SERIAL IN*5 D-sub 9-pin female x 2 (RS232C x 1, RS422 x 1)
SERIAL OUT*5 D-sub 9-pin male x 1 (RS422 x 1)
REMOTE 1 IN M3 jack x1 for wired remote control
REMOTE 1 OUT M3 jack x1 for link control
REMOTE 2 IN D-sub 9-pin female x 1 for external control (parallel)
LAN RJ-45 (10 Base-T/100 Base-TX) x 1, compatible with PJLink™
Optional board slot*6 With ET-MD77SD1 installed
SERIAL IN:   BNC x 1
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i

SERIAL OUT:   BNC x 1, active through
With ET-MD77SD3 installed
SERIAL IN:   BNC x 1
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 292M compliant 720/50p, 720/60p, 1035/60i, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p

SERIAL OUT:   BNC x 1, active through
With ET-MD100SD4 installed
Link A/Link B IN:   BNC x 1 for each
SD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 259M compliant, 480i, 576i
Single-link HD-SDI signal (YCBCR 4:2:2 10-bit) : SMPTE 292M compliant, 720/50p, 720/60p, 1080/50i, 1080/60i, 1080/25p, 1080/24p, 1080/24sF, 1080/30p
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit) : SMPTE 372M compliant, 1920 x 1080/50i, 1920 x 1080/60i, 1920 x 1080/25p, 1920 x 1080/24p, 1920 x 1080/24sF, 1920 x 1080/30p
Dual-link HD-SDI signal (X'Y'Z' 4:4:4 12-bit) : 2048 x 1080/24p, 2048 x 1080/24sF
With ET-MD77DV installed
DVI-D IN:   DVI-D 24-pin x 1, DVI 1.0 compliant, compatible with HDCP, single link
480p, 576p, 1080/60i, 1080/50i, 1080/24p, 1080/24sF, 1080/25p, 1080/30p, 1080/60p, 1080/50p, 720/60p, 720/50p
VGA (640 x 480) – WUXGA*4 (1,920 x 1,200), compatible with non-interlaced signals only, Dot clock: 25–162 MHz
Keystone correction range Vertical: ±40° (±22° with the ET-D75LE5, ±28° with the ET-D75LE6)
Installation Front/rear, ceiling/floor
Power cord length 9.8'' (3.0 m)
Power supply North America 120-240 VAC, 9-16A, 50/60Hz
Europe, Asia 220-240 VAC, 9-16A, 50/60Hz
Power consumption North America 1,600–1,500 W (10–15 W in standby mode with fan stopped)
Europe, Asia 1,500 W (15 W in standby mode with fan stopped)
Dimensions (W x H x D) 22-3/4'' x 12-19/32'' x 25-5/16'' (578 x 320 x 643 mm) (without lens)
Weight*7 77.2 lbs (35 kg) without lens
Operating temperature*8 32-113 °F (0-45°C)
Operating humidity 10-80% (no condensation)
Supplied accessories Power cord, Wireless/wired remote control unit, Batteries for remote control (AA type for North/South America, R6/LR6 type for Europe / Asia) x 2, Eye bolts (x4), Wire rope

*1: Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*2: Shift range is limited during simultaneous horizontal and vertical shifting.
*3: Smooth image reproduction may not be possible when a motion video signal with a vertical frequency other than 50 or 60 Hz is input.
*4: WUXGA resolution is supported only when the signals are compliant with VESA CVT-RB (Coordinated Video Timing-Reduced Blanking).
*5: Contact your dealers for details when the control using RS-232C or RS-422 is required.
*6: The LAN terminal on the optional board will be inactivated after installation. Use the LAN terminal on the main unit.
*7: Average value. May differ depending on models.
*8: The operating temperature range is 0°C (32°F) to 40°C (104°F) when used in High-Altitude mode (1,400 m [4,593 feet] to 2,700 m [8,858 feet]). Also, if the ambient temperature exceeds 40°C (104°F) (35°C [95°F] in High-Altitude mode) when using all four lamps, the light output may be reduced approximately 30% to protect the projector.

Return to Top