This site shows the new line-up of Panasonic projectors and provides
detailed information for home use and business use projectors.
- Projector Global Home
- Product Line-up
- PT-LW25H Series
- Specifications
PT-LW25H / LX30H / LX26H
| Model | PT-LW25H | PT-LX30H | PT-LX26H | |
|---|---|---|---|---|
| Power supply | 100-240 V AC, 50/60 Hz | |||
| Power consumption | 297 W (0.47 W in Eco standby mode*1, 8.6 W in Network standby mode.) | |||
| LCD panel | Panel size | 15 mm (0.59 inches) diagonal (16:10 aspect ratio) |
16 mm (0.63 inches) diagonal (4:3 aspect ratio) |
14 mm (0.55 inches) diagonal (4:3 aspect ratio) |
| Display method | Transparent LCD panel (x 3, R/G/B) | |||
| Pixels | 1,024,000 (1,280 × 800) x 3, total of 3,072,000 pixels |
786,432 (1,024 × 768) x 3, total of 2,359,296 pixels |
||
| Lens | 1.2x manual zoom, manual focus, F 2.10-2.25, f 19.11-22.94 mm | |||
| Lamp | 230 W × 1, lamp replacement cycle (lamp power: High, Normal/Eco): 3,000 hours/4,000 hours*2 | |||
| Screen size (diagonal) | 0.76-7.62 m (30-300 inch) | |||
| Brightness*3 | 2,500 lm (lamp power: High) | 3,000 lm (lamp power: High) | 2,600 lm (lamp power: High) | |
| Center-to-corner uniformity*3 | 85% | |||
| Contrast*3 | 3,000:1 (full on/full off, lamp power: High, Iris: on) |
2,500:1 (full on/full off, lamp power: High, Iris: on) |
||
| Resolution | 1,280 × 800 pixels*4 | 1,024 × 768 pixels*5 | ||
| Scanning frequency | RGB (analog) | fH: 15-100 kHz, fV: 50-100 Hz, dot clock: 140 MHz or lower (Signals exceeding the dot clock rate of 140 MHz are downsampled.) |
||
| YPBPR (YCBCR) |
fH: 15.75 kHz, fV: 60 Hz [480i(525i)]
fH: 31.50 kHz, fV: 60 Hz [480p(525p)] fH: 45.00 kHz, fV: 60 Hz [720(750)/60p] fH: 33.75 kHz, fV: 60 Hz [1080(1125)/60i]
fH: 15.63 kHz, fV: 50 Hz [576i(625i)]
fH: 31.25 kHz, fV: 50 Hz [576p(625p)] fH: 37.50 kHz, fV: 50 Hz [720(750)/50p] fH: 28.13 kHz, fV: 50 Hz [1080(1125)/50i] |
|||
| VIDEO/S-VIDEO | fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM] |
|||
| Optical axis shift | 13:1 | 6:1 | ||
| Keystone correction range | Vertical: ±30° (±20° when Real-Time Keystone) | |||
| Installation | Ceiling/floor, front/rear | |||
| Terminals | COMPUTER IN 1/ S-VIDEO IN |
D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR /S-VIDEO x 1) (The D-Sub/S-VIDEO conversion cable ET-ADSV is required for inputting S-VIDEO signals.) |
||
| COMPUTER IN 2/ MONITOR OUT | D-sub HD 15-pin (female) x 1 (RGB×1), (input/output selectable using on-screen menu) (When Monitor Out is selected, the COMPUTER IN 1 signal is output.) |
|||
| VIDEO IN | RCA pin × 1 (Composite VIDEO) | |||
| AUDIO IN | RCA pin x 2 (L-R x 1) for VIDEO input | |||
| COMPUTER AUDIO IN | M3 × 1 (L-R x 1) | |||
| SERIAL IN | D-sub 9-pin (male) × 1 for external control (RS-232C compliant) | |||
| LAN | RJ-45 × 1 (for network connection, 10Base-T/100Base-TX, compliant with PJLink™ (class 1)) | |||
| Built-in speaker | 3.2 cm round shape × 1, output power: 1 W (monaural) | |||
| Noise level | 37.0 dB (lamp power: High), 34.1 dB (lamp power: Normal), 29.0 dB (lamp power: Eco) | |||
| Cabinet materials | Molded plastic | |||
| Dimensions (W × H × D) | 349 x 105 x 247 mm (13.7" x 4.1" x 9.7") (with legs at shortest position, not including protruding parts) |
|||
| Weight | Approximately 2.99 kg (6.59 lbs) | |||
| Operating environment | Operating temperature: 5°C-35°C (41°F-95°F), operating humidity: 20%-80% (no condensation) | |||
| Supplied accessories | Power cord x 1*6, wireless remote control unit, batteries (AAA/R03/LR03 type × 2), VGA cable x 1, filter cover, software CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software) |
|||
- *1 When Standby mode is set to Eco, network functions such as standby on via LAN are not available.
Also, only certain commands can be received for external control using the serial terminal.
*2 The values given for the recommended lamp replacement cycles are maximum. The usage environment affects the lamp replacement cycle.
*3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4 Input signals that exceed this resolution will be converted to 1,280 x 800 pixels. - *5 Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.
*6 Power cords available (x 2) for the PT-LW25HEA/LX30HEA/LX26HEA.
PT-LX26 / LX22
| Model | PT-LX26 | PT-LX22 | |
|---|---|---|---|
| Power supply | 100-240 V AC, 50/60 Hz | ||
| Power consumption | 297 W (0.47 W in Eco standby mode*1, 8.6 W in Serial standby mode.) |
287 W (0.47 W in Eco standby mode*1, 7.1 W in Serial standby mode.) |
|
| LCD panel | Panel size | 14 mm (0.55 inches) diagonal (4:3 aspect ratio) | |
| Display method | Transparent LCD panel (x 3, R/G/B) | ||
| Pixels | 786,432 (1,024 × 768) x 3, total of 2,359,296 pixels | ||
| Lens | 1.2x manual zoom, manual focus, F 2.10-2.25, f 19.11-22.94 mm | ||
| Lamp | 230 W × 1, lamp replacement cycle (lamp power: High, Normal/Eco): 3,000 hours/4,000 hours*2 | ||
| Screen size (diagonal) | 0.76-7.62 m (30-300 inch) | ||
| Brightness*3 | 2,600 lm (lamp power: High) | 2,200 lm (lamp power: High) | |
| Center-to-corner uniformity*3 | 85% | ||
| Contrast*3 | 500:1 (full on/full off, lamp power: High) | ||
| Resolution | 1,024 × 768 pixels*4 | ||
| Scanning frequency | RGB (analog) | fH: 15-100 kHz, fV: 50-100 Hz, dot clock: 140 MHz or lower (Signals exceeding the dot clock rate of 140 MHz are downsampled.) |
|
| YPBPR (YCBCR) |
fH: 15.75 kHz, fV: 60 Hz [480i(525i)]
fH: 31.50 kHz, fV: 60 Hz [480p(525p)] fH: 45.00 kHz, fV: 60 Hz [720(750)/60p] fH: 33.75 kHz, fV: 60 Hz [1080(1125)/60i]
fH: 15.63 kHz, fV: 50 Hz [576i(625i)] fH: 31.25 kHz, fV: 50 Hz [576p(625p)] fH: 37.50 kHz, fV: 50 Hz [720(750)/50p] fH: 28.13 kHz, fV: 50 Hz [1080(1125)/50i] |
||
| VIDEO/S-VIDEO | fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60], fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM] |
||
| Optical axis shift | 6:1 | ||
| Keystone correction range | Vertical: ±30° (±20° when Real-Time Keystone) | ||
| Installation | Ceiling/floor, front/rear | ||
| Terminals | COMPUTER IN 1/ S-VIDEO IN |
D-sub HD 15-pin (female) x 1 (RGB/YPBPR/YCBCR /S-VIDEO x 1) (The D-Sub/S-VIDEO conversion cable ET-ADSV is required for inputting S-VIDEO signals.) |
|
| VIDEO IN | RCA pin × 1 (Composite VIDEO) | ||
| SERIAL IN | D-sub 9-pin (male) × 1 for external control (RS-232C compliant) | ||
| Noise level | 37.0 dB (lamp power: High), 34.1 dB (lamp power: Normal), 29.0 dB (lamp power: Eco) | ||
| Cabinet materials | Molded plastic | ||
| Dimensions (W × H × D) | 349 x 105 x 247 mm (13.7" x 4.1" x 9.7") (with legs at shortest position, not including protruding parts) |
||
| Weight | Approximately 2.90 kg (6.39 lbs) | ||
| Operating environment | Operating temperature: 5°C-35°C (41°F-95°F), operating humidity: 20%-80% (no condensation) | ||
| Supplied accessories | Power cord x 1*5, wireless remote control unit, batteries (AAA/R03/LR03 type × 2), VGA cable x 1, filter cover, software CD-ROM (Logo Transfer Software) |
||
- *1 When Standby mode is set to Eco, only certain commands can be received for external control using the serial terminal.
*2 The values given for the recommended lamp replacement cycles are maximum. The usage environment affects the lamp replacement cycle.
*3 Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*4 Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.
*5 Power cords available (x 2) for the PT-LX26EA/LX22EA.
- Caution
- Do not install the projector in locations that are subject to excessive water, humidity, steam or oily smoke. Doing so may result in fire, malfunction or electric shock.
- NOTES ON USE
- 1 The projector uses a high-voltage mercury lamp under high internal pressure. This lamp may break, emitting a popping sound, or fail to illuminate, due to impact or extended use.
- 2 The high-wattage lamp becomes very hot during operation. Please observe the following precautions:
• Never place objects on top of the projector while it is in operation.
• Make sure there is an unobstructed space of 1,000 mm (39-3/8 in) or more around the projector’s exhaust openings.
• If stacking projector units, care must be taken to provide the recommended space between units. These space requirements also apply to installation
where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must match the operating temperature listed in the
specifications table during use. Also, make sure the projector’s intake and exhaust openings are not blocked. Ensure there is sufficient ventilation to
prevent hot air from the exhaust openings being recirculated into the intake opening. - 3 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The lamp replacement cycle varies greatly depending on individual lamp characteristics and usage conditions.
• The brightness of the lamp will gradually decrease with use. - 4 Due to natural characteristics of lamps, screen brightness may fluctuate. This is not an indication of faulty lamp performance.