PT-TW330 Series

Short Throw 1-Chip DLP™ Projectors PT-TW331R/PT-TW330/PT-TW240/PT-TX301R/PT-TX300

Specifications

Model PT-TW331R PT-TW330 PT-TW240
Power supply 100-240 V AC, 50/60 Hz
Power consumption 301 W (0.5 W when STANDBY MODE set to ECO,*1
6.0 W when STANDBY MODE set to NORMAL.*2)
254 W
(0.5 W when
STANDBY MODE set to
ECO,*1 6.0 W when
STANDBY MODE set to
NORMAL.*2)
DLP™ chip Panel size 16.5 mm (0.65 in) (16:10 aspect ratio)
Display method DLP™ chip x 1, DLP™ projection system
Pixels 1,024,000 (1,280 x 800) pixels
Lens Fixed (0.521:1 throw ratio), manual focus F = 2.8, f = 7.51 mm
Lamp 240 W UHM lamp 190 W UHM lamp
Lamp replacement cycle
(Normal / Eco / AUTO)
3,000 / 4,000 (Eco1, Eco2) / 7,500 hours*3 4,000 / 6,000 / 8,500 hours*3
Screen size (diagonal) 1.14-5.72 m (45-225 in), 16:10 aspect ratio
Brightness*4 3,100 lm 2,700 lm
Center-to-corner uniformity*4 80 %
Contrast*4 7,500:1
(full on/full off, During RGB signal input, Color mode: Dynamic, Lamp power: AUTO)
Resolution 1,280 x 800 pixels
(Input signals that exceed this resolution will be converted to 1,280 x 800 pixels.)
Scanning
frequency
HDMI fH: 15-91.1 kHz, fV: 24-85.1 Hz, dot clock: 25-162 MHz
RGB (analog) fH: 15-91.1 kHz, fV: 24-85.1 Hz, dot clock: 162 MHz or lower
YPBPR (YCBCR)
fH: 15.75 kHz, fV: 60 Hz [480i (525i)]
fH: 31.50 kHz, fV: 60 Hz [480p (525p)]
fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p]
fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i]
fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p]
fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
fH: 15.63 kHz, fV: 50 Hz [576i (625i)]
fH: 31.25 kHz, fV: 50 Hz [576p (625p)]
fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p]
fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i]
fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p]
Video fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60],
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Optical axis shift 10:-1.2
Keystone correction range Vertical: ±40° (manual)
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin x 1 (Deep color, compatible with HDCP),
audio signal: linear PCM (Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz)
COMPUTER 1 IN D-sub HD 15-pin (female) x 1 [RGB/YPB(CB)/PR(CR) x 1]
COMPUTER 2 IN D-sub HD 15-pin (female) x 1 [RGB/YPB(CB)/PR(CR) x 1]
MONITOR OUT D-sub HD 15-pin (female) x 1 (The signal selected from computer input 1/2 is output.)
VIDEO IN Pin jack x 1
SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
AUDIO 1 IN M3 x 1 (L-R x 1) (for COMPUTER)
AUDIO 2 IN M3 x 1 (L-R x 1) (for VIDEO)
AUDIO OUT M3 x 1 (L-R x 1) for output (variable)
LAN RJ-45 x 1 (for network connection, 100BASE-TX/10BASE-T,
compliant with PJLink™ (class 1))
Mini USB 1 (for interactive function) -
Built-in speaker 7 x 4 cm oval shape x 1, output power 8 W (monaural)
Cabinet materials Molded plastic (PC)
Dimensions (W x H x D) 288 x 106*5 x 270.5 mm
(11-11/32 x 4-3/16*5
x 10-21/32 in)
288 x 100*5 x 246*6 mm
(11-11/32 x 3-15/16*5 x 9-11/16*6 in)
Weight Approximately 2.7 kg (6 lbs)*7 Approximately 2.5 kg (5.5 lbs)*7
Operation noise*4 37 dB (Lamp power: Normal),
32 dB (Lamp power: Eco1),
29 dB (Lamp power: Eco2)
35 dB (Lamp power: Normal),
29 dB (Lamp power: Eco)
Operating temperature 5-40°C [41-104°F] (Less than 750 m [2,500 ft] above sea level),
5-35°C [41-95°F] (between 750 and 1,500 m [2,500 ft and 5,000 ft] above sea level),
5-30°C [41-86°F] (between 1,500 and 3,000 m [5,000 ft and 10,000 ft] above sea level)
Operating humidity 20-80 % (no condensation)
Supplied accessories Power cord (3 m) x 1*8,
wireless remote control unit x 1,
lithium coin cell battery x 1,
computer cable (1.8 m) x 1,
interactive pen x 2,
batteries for interactive pen
(AAA/R03/LR03 type x 4),
USB cable (5.0 m) x 1,
software CD-ROM
(LightPen3) x 1
Power cord (3 m) x 1*8,
wireless remote control unit x 1,
lithium coin cell battery x 1,
computer cable (1.8 m) x 1
  • * Product numbers vary depending on the market. The general guideline is as follows:
    The product number in the Americas and Taiwan is PT-TW331RU, PT-TW330U and PT-TW240U.
    The product number in Europe (except the UK) and CIS is PT-TW331RE, PT-TW330E and PT-TW240E.
    The product number in the UK, Asia (except Taiwan), Oceania, Middle East, and Africa is PT-TW331REA, PT-TW330EA and PT-TW240EA.
*1
When [LAN (Standby)] / [VGA Out (Standby)] / [In Standby Mode (Audio)] are all set to [Off].
*2
When [LAN (Standby)] / [VGA Out (Standby)] / [In Standby Mode (Audio)] are all set to [On].
*3
This is the maximum value when the lamp is turned on for 2 hours and off for 0.25 hours. If the lamp is turned on more times or kept on for a long time, the lamp replacement cycle will shorten. The usage environment affects the duration of the lamp.
*4
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*5
With legs at shortest position.
*6
With lens at shortest position.
*7
The above values are averages. Actual values may be different according to the product.
*8
Power code (x2) for the PT-TW331REA/TW330EA/TW240EA.
Model PT-TX301R PT-TX300
Power supply 100-240 V AC, 50/60 Hz
Power consumption 301 W (0.5 W when STANDBY MODE set to ECO,*1
6.0 W when STANDBY MODE set to NORMAL.*2)
DLP™ chip Panel size 14 mm (0.55 in) (4:3 aspect ratio)
Display method DLP™ chip x 1, DLP™ projection system
Pixels 786,432 (1,024 x 768) pixels
Lens Fixed (0.626:1 throw ratio), manual focus F = 2.8, f = 7.26 mm
Lamp 240 W UHM lamp
Lamp replacement cycle
(Normal / Eco / AUTO)
3,000 / 4,000 (Eco1, Eco2) / 7,500 hours*3
Screen size (diagonal) 1.02-5.08 m (40-200 in), 4:3 aspect ratio
Brightness*4 3,000 lm
Center-to-corner uniformity*4 80 %
Contrast*4 7,500:1
(full on/full off, During RGB signal input, Color mode: Dynamic, Lamp power: AUTO)
Resolution 1,024 x 768 pixels
(Input signals that exceed this resolution will be converted to 1,024 x 768 pixels.)
Scanning
frequency
HDMI fH: 15-91.1 kHz, fV: 24-85.1 Hz, dot clock: 25-162 MHz
RGB (analog) fH: 15-91.1 kHz, fV: 24-85.1 Hz, dot clock: 162 MHz or lower
YPBPR (YCBCR)
fH: 15.75 kHz, fV: 60 Hz [480i (525i)]
fH: 31.50 kHz, fV: 60 Hz [480p (525p)]
fH: 45.00 kHz, fV: 60 Hz [720 (750)/60p]
fH: 33.75 kHz, fV: 60 Hz [1080 (1125)/60i]
fH: 27.00 kHz, fV: 24 Hz [1080 (1125)/24p]
fH: 56.25 kHz, fV: 50 Hz [1080 (1125)/50p]
fH: 15.63 kHz, fV: 50 Hz [576i (625i)]
fH: 31.25 kHz, fV: 50 Hz [576p (625p)]
fH: 37.50 kHz, fV: 50 Hz [720 (750)/50p]
fH: 28.13 kHz, fV: 50 Hz [1080 (1125)/50i]
fH: 67.50 kHz, fV: 60 Hz [1080 (1125)/60p]
Video fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60],
fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM]
Optical axis shift 10:-1.5
Keystone correction range Vertical: ±40° (manual)
Installation Ceiling/floor, front/rear
Terminals HDMI IN HDMI 19-pin x 1 (Deep color, compatible with HDCP),
audio signal: linear PCM (Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz)
COMPUTER 1 IN D-sub HD 15-pin (female) x 1 [RGB/YPB(CB)/PR(CR) x 1]
COMPUTER 2 IN D-sub HD 15-pin (female) x 1 [RGB/YPB(CB)/PR(CR) x 1]
MONITOR OUT D-sub HD 15-pin (female) x 1 (The signal selected from computer input 1/2 is output.)
VIDEO IN Pin jack x 1
SERIAL IN D-sub 9-pin (female) x 1 for external control (RS-232C compliant)
AUDIO 1 IN M3 x 1 (L-R x 1) (for COMPUTER)
AUDIO 2 IN M3 x 1 (L-R x 1) (for VIDEO)
AUDIO OUT M3 x 1 (L-R x 1) for output (variable)
LAN RJ-45 x 1 (for network connection, 100BASE-TX/10BASE-T,
compliant with PJLink™ (class 1))
Mini USB 1 (for interactive function) -
Built-in speaker 7 x 4 cm oval shape x 1, output power 8 W (monaural)
Cabinet materials Molded plastic (PC)
Dimensions (W x H x D) 288 x 106*5 x 270.5 mm
(11-11/32 x 4-3/16*5 x 10-21/32 in)
288 x 100*5 x 246*6 mm
(11-11/32 x 3-15/16*5 x 9-11/16*6 in)
Weight Approximately 2.7 kg (6 lbs)*7 Approximately 2.5 kg (5.5 lbs)*7
Operation noise*4 37 dB (Lamp power: Normal), 32 dB (Lamp power: Eco1), 29 dB (Lamp power: Eco2)
Operating temperature 5-40°C [41-104°F] (Less than 750 m [2,500 ft] above sea level),
5-35°C [41-95°F] (between 750 and 1,500 m [2,500 ft and 5,000 ft] above sea level),
5-30°C [41-86°F] (between 1,500 and 3,000 m [5,000 ft and 10,000 ft] above sea level)
Operating humidity 20-80 % (no condensation)
Supplied accessories Power cord (3 m) x 1*8,
wireless remote control unit x 1,
lithium coin cell battery x 1,
computer cable (1.8 m) x 1,
interactive pen x 2,
batteries for interactive pen
(AAA/R03/LR03 type x 4),
USB cable (5.0 m) x 1,
software CD-ROM (LightPen3) x 1
Power cord (3 m) x 1*8,
wireless remote control unit x 1,
lithium coin cell battery x 1,
computer cable (1.8 m) x 1
  • * Product numbers vary depending on the market. The general guideline is as follows:
    The product number in the Americas and Taiwan is PT-TX301RU and PT-TX300U.
    The product number in Europe (except the UK) and CIS is PT-TX301RE and PT-TX300E.
    The product number in the UK, Asia (except Taiwan), Oceania, Middle East, and Africa is PT-TX301REA and PT-TX300EA.
*1
When [LAN (Standby)] / [VGA Out (Standby)] / [In Standby Mode (Audio)] are all set to [Off].
*2
When [LAN (Standby)] / [VGA Out (Standby)] / [In Standby Mode (Audio)] are all set to [On].
*3
This is the maximum value when the lamp is turned on for 2 hours and off for 0.25 hours. If the lamp is turned on more times or kept on for a long time, the lamp replacement cycle will shorten. The usage environment affects the duration of the lamp.
*4
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
*5
With legs at shortest position.
*6
With lens at shortest position.
*7
The above values are averages. Actual values may be different according to the product.
*8
Power code (x2) for the PT-TX301REA/TX300EA.
NOTES ON USE
1 The projector uses a high-voltage mercury lamp under high internal pressure. This lamp may break, emitting a popping sound, or fail to illuminate, due to impact or extended use.
2 The high-wattage lamp becomes very hot during operation. Please observe the following precautions:
• Never place objects on top of the projector while it is in operation.
• Make sure there is an unobstructed space of 1,000 mm (3 ft 3 in) or more around the projector’s exhaust openings.
• If stacking projector units, care must be taken to provide the recommended space between units. These space requirements also apply to installation where only one projector unit is operating at one time and the other unit is used as a backup.
• If the projector is placed in a box or enclosure, the temperature of the air surrounding the projector must match the operating temperature listed in the specifications table during use. Also, make sure the projector’s intake and exhaust openings are not blocked. Ensure there is sufficient ventilation to prevent hot air from the exhaust openings being recirculated into the intake opening.
3 The lamp replacement cycle duration becomes shorter if the projector is operated repeatedly for short periods.
• The lamp replacement cycle varies greatly depending on individual lamp characteristics and usage conditions.
• The brightness of the lamp will gradually decrease with use.
4 Due to natural characteristics of lamps, screen brightness may fluctuate. This is not an indication of faulty lamp performance.